« previous next »
Pages: [1]   Go Down

Author Topic: Speaker surround replacement  (Read 3645 times)

Offline Mongojustpawn

  • Double Secret Probation!
  • **
  • Posts: 193
  • Karma: +0/-0
  • Mongo Like Choo-Choo!
Speaker surround replacement
« on: October 16, 2014, 12:26:52 AM »
okay, the Optimus 990 speakers I picked up at the the thrift shop now have surrounds that are disintegrating, thinking I may attempt replacing the surrounds, been checking out YouTube to see what's involved, thoughts, advice appreciated.
Logged
Welcome Back My Friends, To The Show That Never Ends

Offline RuralTom

  • Audio Geek!
  • ***
  • Posts: 420
  • Karma: +0/-0
  • Receiving Aural Pleasure....
Re: Speaker surround replacement
« Reply #1 on: October 16, 2014, 05:49:39 AM »
I replaced the surrounds on a pair of JBLs a few months ago- ifrst surround replacement ever- using the no-shim method and found it to be easy enough.  Takes a little patience then concentrated effort while gluing, but it's not difficult at all.
Logged
preamp: BAT VK-5
amp: Altec 944sa
DAC:  Bel Canto 2.5
CDP: Pioneer Elite DV-47a
Intel NUC server / iFi micro iUSB3.0 / Roon
Spendor FL9

Dicky

  • Guest
Re: Speaker surround replacement
« Reply #2 on: October 16, 2014, 07:52:19 AM »
Clean the old foam off with rubbing alcohol (old glue can stay).  Glue CORRECT foam to cone (center by eye) and let glue set.  Later Run a 10-30hz test tone (get one on YouTube) to center and glue foam to basket, and let set.  Glue gasket on, and once glue dries enjoy.  i have yet to shim a voice coil, and I have yet to have a problem.  8w can chime in on the ease of doing this as well.
Logged

Offline MasterBlaster

  • Administrator
  • *****
  • Posts: 1100
  • Karma: +0/-0
    • Vintage HiFi of Pittsburgh
Re: Speaker surround replacement
« Reply #3 on: October 16, 2014, 09:28:37 PM »
How to refoam a speaker:
How to refoam a speaker

Logged
HT: Audiocontrol Maestro M3, Sunfire 5*200,  Tannoy Mercury MX , SVS PB-12 Sub

Head-Fi: FUBAR IV Plus DAC, Grado SR225

Living Room: Dynaco ST-70 (R&R work done by NATOE), Dynaco PAS Preamp, Jamo C607 towers, MCS 6710 Turntable

SunnyDaze

  • Guest
Re: Speaker surround replacement
« Reply #4 on: October 17, 2014, 06:10:43 PM »
It really is a simple job. The hardest part is being patient.

If you do use a test tone to center the voice coils, be sure to not crank the volume too high. Sometimes the oscillations can loosen up the adhesive on the surrounds.

Just go slowly and do one step at a time.  :)
Logged

Offline Mongojustpawn

  • Double Secret Probation!
  • **
  • Posts: 193
  • Karma: +0/-0
  • Mongo Like Choo-Choo!
Re: Speaker surround replacement
« Reply #5 on: October 17, 2014, 11:01:39 PM »
Anyone familiar with simplyspeakers.com, pro or con?
Logged
Welcome Back My Friends, To The Show That Never Ends

Dicky

  • Guest
Re: Speaker surround replacement
« Reply #6 on: October 17, 2014, 11:39:57 PM »
Very good, but a little pricey
Logged

Offline Sir Thrift-a-Lot

  • Ready For Intervention!
  • ******
  • Posts: 3813
  • Karma: +1/-0
Re: Speaker surround replacement
« Reply #7 on: October 19, 2014, 04:38:23 PM »
You can also generate a 30Hz tone in almost any wave editor (I use Au3).
Logged
Pages: [1]   Go Up
« previous next »