« previous next »
Pages: [1]   Go Down

Author Topic: Carver TFM 35x static issue  (Read 4673 times)

Offline Slim-Shaddy

  • CARVER KILLER!!!
  • ******
  • Posts: 1555
  • Karma: +0/-0
  • Tubes are for boobs
    • This is Bullshit
Carver TFM 35x static issue
« on: April 21, 2011, 01:38:35 PM »
I'm just throwing this out there to see if anyone else has had a similar issue.
My TFM35x has one bad channel. While playing it will suddenly get very distorted to the point where it is hardly putting out any sound at all. To eliminate all other components I disconnected the interconnects and it puts out a slightly audible static crackle sound through only the faulty channel while idle. I even swapped speakers and it's still through the same channel. If anyone has any ideas, please let me know before I take it in for repair. The issue is something the amp has had since I bought it, but I just realized it was the amp today after swapping cd players (I was under the assumption the cd player was the faulty unit).
Thanks,
Ed
Logged
I am confident that an SL-1200 is capable of outperforming turntables of much higher expense with minor modification.

BB3

  • Guest
Re: Carver TFM 35x static issue
« Reply #1 on: April 21, 2011, 03:45:07 PM »
Shape-Shifter, there's only one thing left to do my friend............bring it to Tom at the shop.
There's no doubt in my mind that he'll know what to do. I apologize for not knowing what's causing the problem myself, Sir.

---------Bill(BB3)
Logged

Offline Kingman

  • Southern Commander
  • *****
  • Posts: 3127
  • Karma: +0/-0
  • OCCD...I GOT IT BADD!!!!!!!!!
Re: Carver TFM 35x static issue
« Reply #2 on: April 21, 2011, 04:26:34 PM »
Ed, the only thing to try is de-oxit. Spray everything inside but the plastic liberally with it and let it dry a while. Then try again. If not, Tom's the answer.
Logged
IN REALITY IT ONLY MATTERS WHAT IT SOUNDS LIKE TO YOU!!!!!

Offline F1nut

  • Ball Buster
  • *****
  • Posts: 544
  • Karma: +0/-0
Re: Carver TFM 35x static issue
« Reply #3 on: April 22, 2011, 12:45:09 AM »
The first thing to look for is a cold solder joint.
Logged
  'Political Correctness'.........defined

"A doctrine fostered by a delusional, illogical minority and rabidly promoted by an unscrupulous mainstream media, which holds forth the proposition that it is entirely possible to pick up a turd by the clean end."
 

Offline Slim-Shaddy

  • CARVER KILLER!!!
  • ******
  • Posts: 1555
  • Karma: +0/-0
  • Tubes are for boobs
    • This is Bullshit
Re: Carver TFM 35x static issue
« Reply #4 on: April 22, 2011, 10:53:11 AM »
Quote from: F1nut on April 22, 2011, 12:45:09 AM
The first thing to look for is a cold solder joint.

Where on the board should I look and which board should I look at?
Logged
I am confident that an SL-1200 is capable of outperforming turntables of much higher expense with minor modification.

Offline F1nut

  • Ball Buster
  • *****
  • Posts: 544
  • Karma: +0/-0
Re: Carver TFM 35x static issue
« Reply #5 on: April 22, 2011, 03:45:12 PM »
You'll want to look at the bottom of the boards where the solder is at.

Finding a cold solder joint is not always easy. A good solder joint is shiny, a bad one is dull/flat.
Logged
  'Political Correctness'.........defined

"A doctrine fostered by a delusional, illogical minority and rabidly promoted by an unscrupulous mainstream media, which holds forth the proposition that it is entirely possible to pick up a turd by the clean end."
 

Offline Falcon

  • Polk Killer
  • ****
  • Posts: 1131
  • Karma: +0/-0
Re: Carver TFM 35x static issue
« Reply #6 on: April 22, 2011, 03:57:16 PM »
Ed, you are lucky to be near Tom.   Just take it to him, he is the master of Carver repair!!
Logged

Offline OCCD

  • Woof
  • Ready For Intervention!
  • ******
  • Posts: 1741
  • Karma: +0/-0
  • glub glub glub
    • Vintage HiFi of Pittsburgh
Re: Carver TFM 35x static issue
« Reply #7 on: April 23, 2011, 01:56:09 AM »
It is fixed.
Logged
Do you want ants? Because THAT'S HOW YOU GET ANTS!

Offline F1nut

  • Ball Buster
  • *****
  • Posts: 544
  • Karma: +0/-0
Re: Carver TFM 35x static issue
« Reply #8 on: April 23, 2011, 02:44:56 AM »
So, what was the issue?
Logged
  'Political Correctness'.........defined

"A doctrine fostered by a delusional, illogical minority and rabidly promoted by an unscrupulous mainstream media, which holds forth the proposition that it is entirely possible to pick up a turd by the clean end."
 

Offline MasterBlaster

  • Administrator
  • *****
  • Posts: 1100
  • Karma: +0/-0
    • Vintage HiFi of Pittsburgh
Re: Carver TFM 35x static issue
« Reply #9 on: April 23, 2011, 08:06:32 AM »
Logged
HT: Audiocontrol Maestro M3, Sunfire 5*200,  Tannoy Mercury MX , SVS PB-12 Sub

Head-Fi: FUBAR IV Plus DAC, Grado SR225

Living Room: Dynaco ST-70 (R&R work done by NATOE), Dynaco PAS Preamp, Jamo C607 towers, MCS 6710 Turntable

Offline Slim-Shaddy

  • CARVER KILLER!!!
  • ******
  • Posts: 1555
  • Karma: +0/-0
  • Tubes are for boobs
    • This is Bullshit
Re: Carver TFM 35x static issue
« Reply #10 on: April 23, 2011, 08:09:55 AM »
Quote from: F1nut on April 23, 2011, 02:44:56 AM
So, what was the issue?

Yeah?? What was it?
Logged
I am confident that an SL-1200 is capable of outperforming turntables of much higher expense with minor modification.

Offline OCCD

  • Woof
  • Ready For Intervention!
  • ******
  • Posts: 1741
  • Karma: +0/-0
  • glub glub glub
    • Vintage HiFi of Pittsburgh
Re: Carver TFM 35x static issue
« Reply #11 on: April 23, 2011, 02:33:53 PM »
two transistors, two caps, and two resistors.  Come and get it.
Logged
Do you want ants? Because THAT'S HOW YOU GET ANTS!

Offline Slim-Shaddy

  • CARVER KILLER!!!
  • ******
  • Posts: 1555
  • Karma: +0/-0
  • Tubes are for boobs
    • This is Bullshit
Re: Carver TFM 35x static issue
« Reply #12 on: April 23, 2011, 08:57:47 PM »
Anders, you are the man. Tom, you have one badass tech at your shop. Dropped it off and done within, what? 8 hours? Spectacular!!!!!!!!!
Logged
I am confident that an SL-1200 is capable of outperforming turntables of much higher expense with minor modification.
Pages: [1]   Go Up
« previous next »